← Basin groundwater

HYLAND HILLS PARKS & REC LFH-3

Monitored well · 153045 · Division 1 · Water District 2

Its well permit here · Well permit at DWR ↗

Source DWR administrative record · verify at DWR well record ↗ Source DWR administrative record · verify at DWR permit record ↗

Unclassified

No aquifer or designated-basin assignment — administrative world unknown, kept out of recharge math.

Water-level record

No water-level measurements are cached for this well. It is in the well inventory — permit, construction and aquifer below — but nobody has logged a level we hold.

Geophysical log

DWR holds a geophysical log for this well, run 2019-11-18 (gamma, resistivity, spontaneous_potential). DWR's log page.

Formation picks (DWR)

AquiferTop ftBase ftNet sand ft
LARAMIE-FOX HILLS1070 1458

Net sand is DWR's own reading of the log (its gLogThickness), not the gross interval.

Net sand per aquifer, from the gamma curve

Computed here from DWR's own digital log (LAS): linear gamma index, clean/shale lines at p10/p90 of the gamma over the interval, sand where Vsh < 0.4, beds under 1.0 ft merged. DWR’s own pick is beside it, never averaged with it.

AquiferInterval ftNet sand ftNet / grossDWR net sand ftDifference ft
LARAMIE-FOX HILLS1070–1458 249 0.64

A gamma cutoff is a convention, not a measurement. Against DWR’s own picks on 50 wells this one correlates at r 0.86 with a median error near 30% and no bias (how it was scored).

Curves digitized from the scan

Hydrohistorian traced the scanned log automatically. 4 curves passed the confidence gate; 83 did not and are listed with the reason. Screening data: the scan stays the record.

CurveInterval ftCoverageVerdict Curves like this one scored
CONDUCTIVITY(mmho/m) (CONDUCTIVITY(mmho/m)) -4–7021 28% not used: coverage 29%; ambiguous rows 23%; scale OCR confidence 0.69; curve name not recognized: 'CONDUCTIVITY(mmho/m)'
Deep Resistivity (Ohm-m) -4–7021 9% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); coverage 9%; ambiguous rows 31%
Shallow Resistivity (Ohm-m) -4–7021 85% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 50%; curve class not verified by the benchmark: Shallow Resistivity traced as solid
Spontaneous Potential (mV) -4–7021 84% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 42%; SP: the printed scale is a span with an unknown offset, and the benchmark could not verify the shape (median r 0.28 after offset removal)
CORRECTION (g/cc) -3–2078 22% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); coverage 22%; ambiguous rows 28%; curve name not recognized: 'CORRECTION'
CORRECTION (g/cc) -3–2078 86% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 58%; curve name not recognized: 'CORRECTION'
DCAL (in) -3–2078 24% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); coverage 24%; ambiguous rows 32%; curve name not recognized: 'DCAL'
DCAL (in) -3–2078 88% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 46%; curve name not recognized: 'DCAL'
DPOR (pu) -3–2078 17% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); coverage 17%; ambiguous rows 37%; curve name not recognized: 'DPOR'
Gamma Ray (GAPI) -3–2078 13% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); coverage 14%; ambiguous rows 52%
LINETENSION (Ib) -3–2078 88% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 66%; curve name not recognized: 'LINETENSION'
LINETENSION (Ib) -3–2078 12% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); coverage 13%; ambiguous rows 52%; curve name not recognized: 'LINETENSION'
Line Tension (Ib) -3–229 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 68%; curve name not recognized: 'Line Tension'
Shallow Resistivity (Ohm-m) -3–229 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 23%; curve class not verified by the benchmark: Shallow Resistivity traced as solid
Spontaneous Potential (mV) -3–229 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 59%; SP: the printed scale is a span with an unknown offset, and the benchmark could not verify the shape (median r 0.28 after offset removal)
Line Tension (Ib) 250–779 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 80%; curve name not recognized: 'Line Tension'
Shallow Resistivity (Ohm-m) 250–779 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 48%; curve class not verified by the benchmark: Shallow Resistivity traced as solid
Spontaneous Potential (mV) 250–779 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 50%; SP: the printed scale is a span with an unknown offset, and the benchmark could not verify the shape (median r 0.28 after offset removal)
Line Tension (Ib) 800–1329 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 80%; curve name not recognized: 'Line Tension'
Shallow Resistivity (Ohm-m) 800–1329 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 51%; curve class not verified by the benchmark: Shallow Resistivity traced as solid
Spontaneous Potential (mV) 800–1329 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 49%; SP: the printed scale is a span with an unknown offset, and the benchmark could not verify the shape (median r 0.28 after offset removal)
Line Tension (Ib) 98–273 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 58%; curve name not recognized: 'Line Tension'
Shallow Resistivity (Ohm-m) 98–273 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 15%; curve class not verified by the benchmark: Shallow Resistivity traced as solid
Spontaneous Potential (mV) 98–273 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 43%; SP: the printed scale is a span with an unknown offset, and the benchmark could not verify the shape (median r 0.28 after offset removal)
Line Tension (Ib) 298–493 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 68%; curve name not recognized: 'Line Tension'
Shallow Resistivity (Ohm-m) 298–493 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 39%; curve class not verified by the benchmark: Shallow Resistivity traced as solid
Spontaneous Potential (mV) 298–493 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 46%; SP: the printed scale is a span with an unknown offset, and the benchmark could not verify the shape (median r 0.28 after offset removal)
Line Tension (Ib) 498–713 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 59%; curve name not recognized: 'Line Tension'
Shallow Resistivity (Ohm-m) 498–713 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 35%; curve class not verified by the benchmark: Shallow Resistivity traced as solid
Spontaneous Potential (mV) 498–713 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 20%; SP: the printed scale is a span with an unknown offset, and the benchmark could not verify the shape (median r 0.28 after offset removal)
Line Tension (Ib) 748–933 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 67%; curve name not recognized: 'Line Tension'
Shallow Resistivity (Ohm-m) 748–933 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 44%; curve class not verified by the benchmark: Shallow Resistivity traced as solid
Spontaneous Potential (mV) 748–933 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 40%; SP: the printed scale is a span with an unknown offset, and the benchmark could not verify the shape (median r 0.28 after offset removal)
Line Tension (Ib) 948–1153 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 67%; curve name not recognized: 'Line Tension'
Shallow Resistivity (Ohm-m) 948–1153 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 42%; curve class not verified by the benchmark: Shallow Resistivity traced as solid
Spontaneous Potential (mV) 948–1153 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 47%; SP: the printed scale is a span with an unknown offset, and the benchmark could not verify the shape (median r 0.28 after offset removal)
Line Tension (Ib) 1198–1373 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 63%; curve name not recognized: 'Line Tension'
Shallow Resistivity (Ohm-m) 1198–1373 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 32%; curve class not verified by the benchmark: Shallow Resistivity traced as solid
Spontaneous Potential (mV) 1198–1373 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 43%; SP: the printed scale is a span with an unknown offset, and the benchmark could not verify the shape (median r 0.28 after offset removal)
Line Tension (Ib) 1298–1473 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 67%; curve name not recognized: 'Line Tension'
Shallow Resistivity (Ohm-m) 1298–1473 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 38%; curve class not verified by the benchmark: Shallow Resistivity traced as solid
Spontaneous Potential (mV) 1298–1473 97% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 37%; SP: the printed scale is a span with an unknown offset, and the benchmark could not verify the shape (median r 0.28 after offset removal)
CORRECTION (g/cc) 10–259 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 81%; curve name not recognized: 'CORRECTION'
DCAL (in) 10–259 37% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); coverage 38%; ambiguous rows 6%; curve name not recognized: 'DCAL'
DPOR (pu) 10–259 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 97%; curve name not recognized: 'DPOR'
Gamma Ray (GAPI) 10–259 99% not used: ambiguous rows 57%
LINETENSION (Ib) 10–259 30% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); coverage 31%; ambiguous rows 39%; curve name not recognized: 'LINETENSION'
CORRECTION (g/cc) 300–809 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 77%; curve name not recognized: 'CORRECTION'
DCAL (in) 300–809 40% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 20%; curve name not recognized: 'DCAL'
DPOR (pu) 300–809 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 93%; curve name not recognized: 'DPOR'
Gamma Ray (GAPI) 300–809 99% not used: ambiguous rows 66%
LINETENSION (Ib) 300–809 37% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); coverage 37%; ambiguous rows 27%; curve name not recognized: 'LINETENSION'
CORRECTION (g/cc) 850–1359 95% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 68%; curve name not recognized: 'CORRECTION'
DCAL (in) 850–1359 40% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 23%; curve name not recognized: 'DCAL'
DPOR (pu) 850–1359 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 82%; curve name not recognized: 'DPOR'
Gamma Ray (GAPI) 850–1359 99% not used: ambiguous rows 56%
LINETENSION (Ib) 850–1359 33% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); coverage 34%; ambiguous rows 24%; curve name not recognized: 'LINETENSION'
CORRECTION (g/cc) 98–301 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 53%; curve name not recognized: 'CORRECTION'
DCAL (in) 98–301 65% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 41%; curve name not recognized: 'DCAL'
DPOR (pu) 98–301 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 82%; curve name not recognized: 'DPOR'
Gamma Ray (GAPI) 98–301 100% not used: ambiguous rows 53%
LINETENSION (Ib) 98–301 66% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 30%; curve name not recognized: 'LINETENSION'
CORRECTION (g/cc) 348–521 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 69%; curve name not recognized: 'CORRECTION'
DCAL (in) 348–521 65% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 31%; curve name not recognized: 'DCAL'
DPOR (pu) 348–521 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 79%; curve name not recognized: 'DPOR'
Gamma Ray (GAPI) 348–521 100% pass r 0.99 median, error 0.6% of scale, 7% below r 0.8 (n 411) LAS
LINETENSION (Ib) 348–521 71% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 33%; curve name not recognized: 'LINETENSION'
CORRECTION (g/cc) 548–741 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 60%; curve name not recognized: 'CORRECTION'
DCAL (in) 548–741 67% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 29%; curve name not recognized: 'DCAL'
DPOR (pu) 548–741 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 75%; curve name not recognized: 'DPOR'
Gamma Ray (GAPI) 548–741 100% pass r 0.99 median, error 0.6% of scale, 7% below r 0.8 (n 411) LAS
LINETENSION (Ib) 548–741 70% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 30%; curve name not recognized: 'LINETENSION'
CORRECTION (g/cc) 748–961 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 77%; curve name not recognized: 'CORRECTION'
DCAL (in) 748–961 62% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 42%; curve name not recognized: 'DCAL'
DPOR (pu) 748–961 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 84%; curve name not recognized: 'DPOR'
Gamma Ray (GAPI) 748–961 100% not used: ambiguous rows 54%
LINETENSION (Ib) 748–961 72% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 28%; curve name not recognized: 'LINETENSION'
CORRECTION (g/cc) 998–1181 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 57%; curve name not recognized: 'CORRECTION'
DCAL (in) 998–1181 66% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 33%; curve name not recognized: 'DCAL'
DPOR (pu) 998–1181 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 67%; curve name not recognized: 'DPOR'
Gamma Ray (GAPI) 998–1181 100% pass r 0.99 median, error 0.6% of scale, 7% below r 0.8 (n 411) LAS
LINETENSION (Ib) 998–1181 69% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 32%; curve name not recognized: 'LINETENSION'
CORRECTION (g/cc) 1198–1401 99% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 46%; curve name not recognized: 'CORRECTION'
DCAL (in) 1198–1401 62% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 45%; curve name not recognized: 'DCAL'
DPOR (pu) 1198–1401 100% not used: solid curve on a Phoenix/Pioneer print: only the gamma is verified (its resistivity scales are log/backup scales the parser does not read, benchmark r < 0.5); ambiguous rows 56%; curve name not recognized: 'DPOR'
Gamma Ray (GAPI) 1198–1401 100% pass r 0.99 median, error 0.6% of scale, 7% below r 0.8 (n 411) LAS
LINETENSION (Ib) 1198–1401 66% not used: dashed curve on a Phoenix/Pioneer print: not traceable (benchmark median r 0.38 for the shallow resistivity, 0.00 before the dash/dot split); ambiguous rows 34%; curve name not recognized: 'LINETENSION'

"Curves like this one" is the benchmark row for this curve's class: curves of the same name traced the same way, scored against DWR's own digital log of the same run. r is correlation (the print's own smoothing allowed for); error is mean absolute error as a share of the track's printed range; "below r 0.8" is the share of passing curves in the class that still disagreed with DWR's log, which this curve's own numbers cannot rule out.

The LAS files and every verdict are in the statewide groundwater release (/data, table gw_digitized); the MCP server's gw_digitized_curves and gw_net_sand work from them. How well the tracer does was measured against DWR's own digital logs.

The well itself

Total depth1470.0 ft
Perforated interval1102.0–1127.0 ft
Ground elevation5410.0 ft
Permit83431
Location39.87000, -105.05000
What this page is not

Monitoring records are irregular: measurements cluster where somebody chose to look, so a trend describes this well's record, not the aquifer as a whole. Levels are DWR's published measurements, unedited. A trend here is not a prediction, and it is not a determination about anyone's water right.